Readers ask: How To Install Cement Siding?

Readers ask: How To Install Cement Siding?

Can I install Hardie siding myself?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

What nails do you use for Hardie siding?

NAIL TYPE: Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.

Do you need plywood behind Hardie board?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Be sure that the siding installed is dry. Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches.

Do you nail or screw Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.

You might be interested:  FAQ: How To Install Aluminum Siding?

Can you install Hardie siding directly to studs?

HardiePlank┬« lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements.

Can I use roofing nails for Hardie siding?

You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall.

Does siding need to be nailed into studs?

Vinyl siding must never be applied directly to studs without sheathing.

Can I use screws for Hardie siding?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel.

Do termites eat Hardie board?

Do Termites Eat Hardie Board? Although termites do eat wood, they cannot get to the wood in Hardie Board siding because of the fiber cement materials throughout the product.

Do I need vapor barrier behind Hardibacker?

Hardibacker doesn’t need a vapor barrier or waterproofing except you do need to tape and thinset the joints.

Does Hardie board need a vapor barrier?

Do I need vapor barrier behind Hardibacker? You need to install a vapor barrier to the studs at the very least, and you must alway mud and tape the seams with fiberglass cement backerboard tape. Backerboard is water-permeable, and will not stop moisture from entering the wall cavity.

You might be interested:  How To Cut Siding For Gable Ends?

How do you attach things to Hardie board?

Generally speaking, items can be attached to James Hardie siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).

Does Hardie board crack?

Because Hardie siding is so stiff any movement of the house can cause cracks in the siding which are typical of any rigid masonry product.

Does Hardie board need to be painted?

What is Hardie Plank? Hardie Plank is a newer composite material made of concrete substrate. Hardie Plank is also called fiber cement siding. While it’s far heavier than aluminum, vinyl or wood, it is extremely durable and typically only needs a new paint every ten to twenty years for maintenance.


Leave a Reply

Your email address will not be published. Required fields are marked *