Readers ask: How To Install Cedar Shake Siding Shingles?

Readers ask: How To Install Cedar Shake Siding Shingles?

What do I put under cedar shingles?

The Cedar Shake and Shingle Bureau recommends installation over Type 30 asphalt felt underlayment for red cedar shingles and shakes. Install the felt paper with minimum 6-inch overlaps on vertical joints, 2 inches on horizontal laps, and 4 inches wrapped each way at inside and outside corners.

How do you attach cedar shakes?

Start at the bottom of the wall at one end. Align the thick, lower edge of a cedar shake at the lower edge of the siding or shear wall. Align one of the vertical edges at the edge of the trim or corner of the wall. Attach the shake with a pair of 5d galvanized box nails and a shingle hatchet or hammer.

How much do you overlap cedar shingles?

Leave a gap of approximately 1/8” to 1/4” (0.3 to 0.6 cm) between neighboring shingles to allow for expansion due to moisture. Joints of successive courses must always be offset by at least 1 1/2” (3.8 cm) to prevent water build-up. Treat shingle imperfections the same way.

You might be interested:  How Much I Can Pay For Wood Siding?

Where do you nail cedar shingles?

Place two nails 2 cm (3/4 in.) from each edge of the cedar shingle and 4 cm (1 1/2 in.) above the exposure. To avoid buckling, allow 3 to 6 mm (1/8 to 1/4 in.)

Are cedar shingles waterproof?

Are cedar shingles waterproof? Cedar wood shingles are prone to mold, mildew, and insects. It is important to note that the wood on a cedar roof is not intended to be waterproof, and is therefore quite susceptible to wind-driven rain. Any natural product exposed to water is vulnerable to mold, mildew and erosion.

What type of nails should I use for cedar siding?

Hot-Dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.

Can you use roofing nails for cedar shakes?

At Cedar Roof Coatings, we advise against the use of plain steel nails to keep the cedar roofing stain-free over time. Plain steel nails and copper nails can react adversely with the natural oils in cedar and can rust and disintegrate.

How much does cedar shake siding cost?

Cedar shake siding costs between $6 and $12 per square foot for materials and installation. Shingle siding costs $6 to $10 per square foot. To put cedar siding on an entire house, it costs $9,000 to $19,000 or more, depending on the size of the home.

You might be interested:  Readers ask: When Was Aluminum Siding First Used?

What is the difference between wood shingles and wood shakes?

Cedar shakes are split off while shingles are sawn smooth on both sides and cut tapered. Lastly, shakes are thicker than shingles. Durability – Generally speaking, cedar shakes are more durable and last longer than shingles because they are thicker and made from premium grade wood.

How far do you space cedar shingles?

The split face is always installed to the weather, the sawn face to the deck. The starter course may be one or two layers of cedar shingles or shakes, overlaid with the desired shake. Spacing between adjacent shakes should be a minimum of 9mm and maximum of 16mm.

How many nails are in a square of cedar shingles?

The standard required amount of nails for cedar shingles is 320 pieces per square. For areas with a lot of wind, six nails for each shingle might be needed, which means you need 480 nails for each square.

What size nails do you use for cedar shingles?

Staples must be 16 gauge with crowns 7/16″ minimum horizontal, maximum 3/4″ horizontal to the Certi-label shake or shingle butt. Fasteners, two (2) per shake or shingle, shall be applied approximately 3/4″ from the edge and approximately 1 1/2″ above the exposure line.

Can you use a brad nailer for cedar shingles?

A regular brad nailer? That will make our task easy as we will only need to identify a nail gun that shoots the accepted nails.. Now, here is what the CSSB says about fasteners for cedar shingles: “ Use either rust-resistant staples or shingle nails (1-1/4” to 1-1/2” long), galvanized, in stainless steel or aluminum”.

You might be interested:  What Type Of Nails For Cedar Siding?

Can you staple cedar shake siding?

The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone – stainless steel staples Type 304 or Type 316 must be used.


Leave a Reply

Your email address will not be published. Required fields are marked *