Readers ask: Hardie Board Siding Being Installed On House Next Door, What Risks To Me?

Readers ask: Hardie Board Siding Being Installed On House Next Door, What Risks To Me?

Is fiber cement siding dangerous?

Cutting fiber cement siding generates respirable crystalline silica, a known human carcinogen. Inhaling too much silica can lead to silicosis, lung cancer, and COPD. Special saw blades, ventilation, and respirators can be used to limit silica inhalation to a safe level during installation.

Is Hardie board dust dangerous?

Breathing dust that contains respirable crystalline silica can lead to silicosis, a deadly lung disease. Respirable dust is that fraction of the aerosol that is small enough to reach the deeper, gas-exchange regions of the lungs.

Is Hardie board safe?

No, there’s no need to. This is not a product issue – our fiber cement products are inherently safe when cut according to our guidelines.

Does Hardie board get mold?

It is highly susceptible to mold and mildew. Hardie Plank has many seams and the seams must be sealed or water can infiltrate behind the siding. It can crack and if it does, you must tear the whole wall down in order to replace just one plank. It is mold and mildew resistant.

You might be interested:  Readers ask: How To Prepare Hardie Board Siding For Painting?

How long does fiber cement siding last?

With regular TLC, your fiber cement siding can last 50 years or more—now that’s what I call long -lasting!

Do you need a special blade to cut Hardie board?

Cement Board – Cutting Tools For some types of Hardie board, you ‘ll need a power tool with a cement board blade with a carbide tip to cut the board. Carbide-tipped blades are made specifically for this kind of work. Once prepared, cut the Hardie board as you would any other material.

What are the signs of silicosis?

These commonly include bronchitis-like symptoms such as persistent cough, shortness of breath and difficulty breathing. People also suffer from weakness, fatigue, fever, night sweats, leg swelling and bluish discoloration of the lips.

Can you screw Hardie siding?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel.

How much does it cost to side a 1500 sq ft house?

Aluminum siding costs An average 1,500 square foot house would cost around $7,700 for standard aluminum siding and upwards of $11,000 for custom grades after labor and material costs.

Is Hardie board expensive?

The Cost. Hardie board siding runs about $0.70 to $5.25 per square foot. This could lead to a total cost of anywhere from $4,700 to $13,300.

How often should you paint hardiplank?

Hardie Plank is a newer composite material made of concrete substrate. Hardie Plank is also called fiber cement siding. While it’s far heavier than aluminum, vinyl or wood, it is extremely durable and typically only needs a new paint every ten to twenty years for maintenance.

You might be interested:  What Kind Of Nails For Cedar Siding?

What nails should I use for Hardie siding?

NAIL TYPE: Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.

Does Hardie board need plywood backing?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Be sure that the siding installed is dry. Otherwise, it might shrink at butt joints.

Can you use a nail gun on hardiplank?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Use 6d or 8d galvanized or stainless siding nails and install a single nail about 1-in.


Leave a Reply

Your email address will not be published. Required fields are marked *