Quick Answer: What Kind Of Screws To Use For Ipe Wood Siding?

Quick Answer: What Kind Of Screws To Use For Ipe Wood Siding?

How do you install ipe wood?

Face Screw / Plug Method: Countersink 3/8″ holes into face of deck boards. Predrill 1/8″ pilot holes completely through the deck boards. Screw the deck boards down with stainless screws. 3/8″ Ipe plugs are then glued into the holes with waterproof glue (i.e. Gorilla brand glue, Epoxy, etc.)

What is the best hidden deck fasteners for IPE?

That’s why we developed the Mataverde Hidden Deck Fastener. It is the best and most effective hidden fastener for Ipe decking and other high density hardwood decking materials.

How do you install tongue and groove IPE?

For installation, we suggest that you pre-drill a hole on a 45-degree angle where the tongue and the face meet. You will see a slight v- groove in this corner. Then, on that same 45-degree angle, drive a trim head screw through the pre-drilled hole, through the deck board into the floor joist.

How far can you span IPE decking?

Deck Board Gap Spacing Anytime installing Ipe decking, make sure to set a space between deck boards of 3/32″. The variation in gap spacing is to make certain that the decking has room to expand and contract depending on the material used and the atmosphere where it is installed. This also allows for adequate air flow.

You might be interested:  Who Sell Sheet Meteal Siding?

How do you acclimate ipe wood?

The proper way to acclimate wood is to let it sit in the area where it will be built for a period of at least 7 days. Depending on your climate, and the time of year you install your deck, this acclimation period can be anywhere between 7 – 14 days. Never let your wood sit directly on top of the ground or concrete.

Does ipe wood crack?

Ipe Decking dries and contracts, leaving tiny cracks in the face or at the ends of the boards. These tiny cracks are known as checks. Face checking is a very normal and is very difficult to see. It does not affect the durability, longevity or water-resistant benefits.

How much does it cost to install IPE decking?

Installing Ipe Decking Boards Per Square Foot Installation of the deck planks ranges between $20 and $35 per square foot. The cost includes both labor and materials such as hinges, nails and screws. It’s higher than most other lumber because this material is so dense, it requires special equipment to drill holes.

Does IPE need to acclimate?

Like any exterior wood, Ipe needs to acclimate properly for best results. If you take care of your Ipe decking, especially initially, it will take care of you by lasting longer and performing better.”

What is the best hidden deck fastener?

Best Hidden Fasteners for Decking

  • Camo Hidden Fasteners.
  • Eb-Ty Hidden Deck Fastener.
  • Tiger Claw Hidden Fastener.
  • Trex Hideaway Hidden Fastener.
  • Cortex Hidden Fastener.
  • ConceaLoc Hidden Fastener.
  • Mantis Hidden Fastener.
  • Ipe Clip Hidden Fastener.
You might be interested:  How To Install Outside Receptacle On Siding?

Can you nail ipe wood?

Ipe Wood Is Not to be Nailed No, ipe is brittle because it is so dense, and if you hammer nails on the edges, it is likely to split. Therefore, the best option might be to use stainless steel screws on the wood.

Are hidden deck fasteners worth it?

Hidden deck fasteners are a nice way to keep the surface of your deck looking clear and unencumbered. But they are not the right fastener for all decks. In fact, using hidden deck fasteners inappropriately is a formula for failure. Some deck projects require the stronger fastening power of face screws.

How much does ipe wood cost?

Ipe is more expensive than many woods. On average, ipe costs $3.50 to $5 per square foot “and the cost of labor will increase the total price to around $20 per square foot,” according to Improvenet.

Does ipe wood expand and contract?

Well, not literally, but throughout the course of the year hardwood decking will absorb and release moisture from the air. This process makes the wood expand and contract. For ipe decking, the average rate of shrinkage is roughly 1/16″ on 4″ wide boards and 3/32″ on 6″ wide boards.

Is tongue and groove waterproof?

Similarly, the tongue and groove panels are 100% waterproof. All of our panels are made out of non-porous, waterproof materials that don’t soak up moisture. The water stays on the surface where it can be wiped away with ease.


Leave a Reply

Your email address will not be published. Required fields are marked *