Question: How To Install Hardie Board Shingle Siding?

Question: How To Install Hardie Board Shingle Siding?

What do you fasten Hardie board with?

Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.

Can I install Hardie siding myself?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

Do you nail or screw Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.

What is the overlap for Hardie siding?

Each row of siding should overlap by 1¼” or more.

You might be interested:  What Is A Square In Siding?

Can you screw into hardiplank?

Can you screw James Hardie siding? If you mean “ can you put screws into James Hardie siding” the answer is yes. Otherwise, you may have landed on the wrong website. James Hardie boards can technically be drilled like wood, but it is best to use a masonry bit to drill this tough fiber-cement board.

Does Hardie board need to be painted?

What is Hardie Plank? Hardie Plank is a newer composite material made of concrete substrate. Hardie Plank is also called fiber cement siding. While it’s far heavier than aluminum, vinyl or wood, it is extremely durable and typically only needs a new paint every ten to twenty years for maintenance.

How much does it cost to have Hardie siding installed?

The average cost to install Hardie siding is $6 and $13 per square foot. Installing Hardiplank shingles on a 1,600 SF house costs $10,000 to $18,000 on average. James Hardie is the most well-known fiber cement siding brand due to its longevity, appearance, fire-resistance, and weather-resistance.

How much does it cost to install hardiplank?

Hardie board siding costs anywhere from $0.80 to $6.00 per square foot material installed on a home. If you were to replace an average size home with 1,500 square ft of materials you could expect to pay anywhere from $1,200 to $9,000 in replacement costs. Insert your zip below to get free local quotes.

Does Hardie board need plywood backing?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Be sure that the siding installed is dry. Otherwise, it might shrink at butt joints.

You might be interested:  Question: How To Cedar Shake Siding?

How long can Hardie board go unpainted?

Pre-primed products can sit for 6 months without paint. Unprimed hardie can sit for 3 months without paint.

Should you caulk Hardie board siding?

Wherever Hardie siding meets a trim board, the company recommends you leave a 1/8” gap between the siding and the trim and apply a 3/8” bead of approved caulking to protect and seal the edge of the siding. This means that Hardie contractors are used to overapplying their caulking and letting it shrink over time.

What is the best nail gun for Hardie siding?

Our Recommended Best Nail Gun for Hardie Trim and Siding

  • NuMax SFR2190 Pneumatic 21 Degree Full Round Head Framing Nailer.
  • PORTER-CABLE 20V MAX Cordless Brad Nailer Kit.
  • Dewalt DW66C-1R Coil Nail Gun for Hardie Siding.
  • Freeman P4FRFNCB Hardie Board Nail Gun.
  • BOSTITCH N66C Coil Siding Nailer.

Can I use a roofing nailer for Hardie siding?

You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall. Our Crews prefer 1 3/4 “ smooth shank roofing nails for Hardie installation.

How is James Hardie siding installed?

James Hardie products can be hand nailed or fastened with a pneumatic tool. Pneumatic fastening is highly recommended. Set air pressure so that the fastener is driven snug with the surface of the siding. A flush mount attachment on the pneumatic tool is recommended.


Leave a Reply

Your email address will not be published. Required fields are marked *