How To Install James Hardie Plank Siding?

How To Install James Hardie Plank Siding?

What nails do you use for Hardie siding?

NAIL TYPE: Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.

Do you need plywood under Hardie board siding?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Be sure that the siding installed is dry. Otherwise, it might shrink at butt joints.

Can I install Hardie siding myself?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

Can you install Hardie plank directly to studs?

HardiePlank ® lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements.

You might be interested:  Question: How Do I Measure The Width Of Vinyl Siding You Tube?

Can you put screws in hardiplank?

James Hardie Building Products recommends keeping nails or screws at least 3/8 inch from the end of a plank. Drill pilot holes, at each mark, one -quarter to one -half inch deep, to make it easier to insert screws and prevent cracking the siding.

Do I need house wrap behind Hardie siding?

With fiber cement siding, the heavy material may compress the wrap so it’s extremely important that a non-woven wrap is used. This is because the heavy siding may lead to a build-up of moisture behind it, which in turn, can lead to mold growth and wood rot if that moisture is not properly addressed.

Do you nail or screw Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.

How long can Hardie board go unpainted?

Pre-primed products can sit for 6 months without paint. Unprimed hardie can sit for 3 months without paint.

Is James Hardie siding worth it?

James Hardie siding is a great, environmentally friendly choice for overall curb appeal and home value. It will give your home a new look and feel to it. It is an attractive choice with guaranteed durability and quality. It provides an amazing return on investment.

Is Hardie board better than vinyl siding?

Both forms of siding have their benefits, but for the most part, James Hardie siding is more durable. While both vinyl and fiber cement are rot resistant and pest resistant, unlike traditional wood planks, Hardie board siding is inflammable, warp resistant, Engineered for Climate®, and impact resistant.

You might be interested:  Often asked: What Was Upson Siding Made From?

How much does it cost to reside a house with Hardie Plank?

Average cost: $1,200 – $9,000 Hardie board siding costs anywhere from $0.80 to $6.00 per square foot material installed on a home. If you were to replace an average size home with 1,500 square ft of materials you could expect to pay anywhere from $1,200 to $9,000 in replacement costs.

Can you use roofing nails for Hardie siding?

You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall.

How do you nail Hardie?

Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.


Leave a Reply

Your email address will not be published. Required fields are marked *