FAQ: What Kind Of Nails To Use For Vinyl Siding?

FAQ: What Kind Of Nails To Use For Vinyl Siding?

What kind of nails should I use for vinyl siding?

Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.

How do you nail vinyl siding?

Do not nail any siding parts too tight. Leave 1/32 inch between the nail head and the vinyl. Vinyl siding must be attached “loosely.” Center nails in slots to permit expansion and contraction of the siding. Drive nails straight and level to prevent distortion and buckling of panel.

Do you have to nail vinyl siding?

Vinyl siding tends to expand and contract considerably with temperature changes. For this reason, manufacturers design it to hang loosely on the nails rather than to be tightly nailed like wood siding. If all the siding is tight, it was installed wrong and should be redone.

You might be interested:  Readers ask: How To Hang Shutters On Siding?

Why are vinyl siding nails aluminum?

Why are these aluminum siding nails galvanized to resist corrosion when they are aluminum? They are pure aluminum, not steel, and not galvanized. You cannot galvanize aluminum. Aluminum does not rust, so best used for siding (won’t streak rust down the side of the building).

Can I use roofing nails for siding?

You can use a roofing nailer (1-3/4″ galvanized nails ) to install siding if you “blind nail ” them, so you won’t see the nail head at all. Use electro, or hot-dipped galvanized steel or aluminum roofing type nails with a diameter of 1/8″ and a nail head of 3/8″ or larger.

Do i need foam board under vinyl siding?

Many people install vinyl siding or concrete board sding to improve the look and value of their home. With budgets tighter than ever now, contractors and do -it-youselfers are tearing off the original siding and installing a thin foam board underneath claiming it will improve the energy efficiency of the property.

Can I install my own vinyl siding?

The truth is, the price of a vinyl siding installation can be cut nearly in half if you’re willing to do the work yourself. Vinyl siding is sold by most home centers and comes with fairly complete instructions. The tool requirements are also modest. For this reason, vinyl must be cut short and nailed loose.

How many sq feet does a box of vinyl siding cover?

A box of vinyl siding contains two “squares.” A square in construction lingo equals 100 square feet, so a box of vinyl siding will cover 200 square feet.

You might be interested:  How To Replace Masonite Siding?

What is under vinyl siding?

The wood that goes under residential siding — exterior sheathing — performs several functions. It adds insulation, waterproofing and structural support for the framing. It also provides a surface on which to nail the siding. The most common sheathing materials include oriented strand board and plywood.

How long should vinyl siding nails be?

The nails should measure at least 1-3/4 inches in length, long enough to penetrate into the nailable base at least 3/4 inch.

How long does vinyl siding last?

To put it simply, vinyl siding lasts a long time. Depending on the quality of the materials and the experience of the contractor that installs it, it can last about 60 years. And with some minimal maintenance on occasion, your vinyl siding can last even longer than that.

Do you need plywood under siding?

Question: Do you put plywood under siding? Answer: If it’s plywood sheathing, yes you can put it under the siding. It’ll be the best structural support for your house.

Can you put insulation under vinyl siding?

Another option for adding insulation to the walls of a home is to use insulated vinyl siding. Similar to blown in insulation, insulated vinyl siding provides r-value for improved energy efficiency.

How do you stagger vinyl siding?

Stagger the siding end laps so that no two courses (rows of panels) are aligned vertically, unless separated by at least three courses. Always overlap joints away from entrances and/or away from the point of greatest traffic. This will improve the overall appearance of the installation (Fig. 37).


Leave a Reply

Your email address will not be published. Required fields are marked *