FAQ: How To Install Hardiplank Shingle Siding?

FAQ: How To Install Hardiplank Shingle Siding?

What do you fasten Hardie board with?

Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.

Can I install Hardie siding myself?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.

How do you nail hardiplank siding?

Fastening Siding

  1. Use hot-dipped galvanized or stainless steel nails.
  2. Nails should penetrate through the sheathing and at least 1” into studs.
  3. Position nails ¾” to 1” from the edge of the siding.
  4. Siding can either be blind nailed at the top or face nailed at the bottom.
You might be interested:  How To Install Vinyl Siding Aroumd A Window?

How many Hardie shingles make a square?

Pieces needed for one square (100sq. ft.) of product coverage = approximately 43, based on maximum 7″ exposure. 16″ or 24″ o.c.

Can you screw into hardiplank?

Can you screw James Hardie siding? If you mean “ can you put screws into James Hardie siding” the answer is yes. Otherwise, you may have landed on the wrong website. James Hardie boards can technically be drilled like wood, but it is best to use a masonry bit to drill this tough fiber-cement board.

Can you install Hardie siding directly to studs?

HardiePlank® lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements.

Do you nail or screw Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.

How much does it cost to have Hardie siding installed?

The average cost to install Hardie siding is $6 and $13 per square foot. Installing Hardiplank shingles on a 1,600 SF house costs $10,000 to $18,000 on average. James Hardie is the most well-known fiber cement siding brand due to its longevity, appearance, fire-resistance, and weather-resistance.

How much does it cost to install hardiplank?

Hardie board siding costs anywhere from $0.80 to $6.00 per square foot material installed on a home. If you were to replace an average size home with 1,500 square ft of materials you could expect to pay anywhere from $1,200 to $9,000 in replacement costs. Insert your zip below to get free local quotes.

You might be interested:  FAQ: How To Replace Corner Vinyl Siding?

Should you caulk Hardie board siding?

Wherever Hardie siding meets a trim board, the company recommends you leave a 1/8” gap between the siding and the trim and apply a 3/8” bead of approved caulking to protect and seal the edge of the siding. This means that Hardie contractors are used to overapplying their caulking and letting it shrink over time.

How long can Hardie board go unpainted?

Pre-primed products can sit for 6 months without paint. Unprimed hardie can sit for 3 months without paint.

What is the best nail gun for Hardie siding?

Our Recommended Best Nail Gun for Hardie Trim and Siding

  • NuMax SFR2190 Pneumatic 21 Degree Full Round Head Framing Nailer.
  • PORTER-CABLE 20V MAX Cordless Brad Nailer Kit.
  • Dewalt DW66C-1R Coil Nail Gun for Hardie Siding.
  • Freeman P4FRFNCB Hardie Board Nail Gun.
  • BOSTITCH N66C Coil Siding Nailer.

Does Hardie board make shingles?

HardieShingle siding is available as straight-edge panels or staggered-edge panels 48 in. long by 16 in high. HardieShingle panels also come as decorative half-round shingles. For smaller coverage areas, individual shingles are also available in 4.2 in, 5.5 in, 6.75 in, 7.25 in & 10 in widths.

How do you stagger Hardie siding?

It’s best to stagger the joints in each successive course to avoid noticeable patterns. Butt joints in adjacent courses should be spaced apart by at least two stud bays for 16-inch, o.c. framing or one bay for 24-inch, o.c. framing.

What colors does Hardie board siding come in?

Statement Collection™ Colors

  • Arctic White.
  • Cobble Stone.
  • Monterey Taupe.
  • Khaki Brown.
  • Pearl Gray.
  • Gray Slate.
  • Boothbay Blue.
  • Evening Blue.

Leave a Reply

Your email address will not be published. Required fields are marked *