FAQ: How To Cut Hardiplank Siding?

FAQ: How To Cut Hardiplank Siding?

What kind of saw blade do you need to cut Hardie board?

x 4-Teeth Polycrystalline Diamond (PCD) Tipped James Hardie /Fiber Cement Saw Blade.

Can you cut Hardie board with a regular saw blade?

You can use a jigsaw, table saw or circular saw, or another tool, as long as it’s equipped with the right kind of blade. Once prepared, cut the Hardie board as you would any other material. Mark your line; align the board against the guard as needed and slowly but firmly make the cut.

Is Hardie board dust dangerous?

Breathing dust that contains respirable crystalline silica can lead to silicosis, a deadly lung disease. Respirable dust is that fraction of the aerosol that is small enough to reach the deeper, gas-exchange regions of the lungs.

What nails should I use for Hardie siding?

NAIL TYPE: Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.

You might be interested:  How To Install Osb Siding?

Do you caulk Hardie board siding?

Wherever Hardie siding meets a trim board, the company recommends you leave a 1/8” gap between the siding and the trim and apply a 3/8” bead of approved caulking to protect and seal the edge of the siding. This means that Hardie contractors are used to overapplying their caulking and letting it shrink over time.

Can I use a framing nailer for Hardie siding?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. You may also find that siding nailers are a few pounds lighter than framing guns.

Can you use a nail gun on hardiplank?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Use 6d or 8d galvanized or stainless siding nails and install a single nail about 1-in.

Is Hardie board waterproof?

HardieBacker® Cement Board with HydroDefense™ Technology is a long-lasting, waterproof solution for walls, floors, and countertops.

How do you cut Hardie board with a circular saw?

Fit your circular saw with a carbide-tipped wood- cutting blade (view example on Amazon), choosing one with as few teeth as possible in order to minimize the amount of dust given off as you saw. Operate your circular saw as you typically would, pushing it slowly and evenly through your cement backer board.

You might be interested:  What Color To Paint Front Door With Tan Siding?

What side of Hardie board faces out?

away from the edges. Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic.

Does hardiplank cause cancer?

Cutting fiber cement siding generates respirable crystalline silica, a known human carcinogen. Inhaling too much silica can lead to silicosis, lung cancer, and COPD.

What are the signs of silicosis?

These commonly include bronchitis-like symptoms such as persistent cough, shortness of breath and difficulty breathing. People also suffer from weakness, fatigue, fever, night sweats, leg swelling and bluish discoloration of the lips.

Does Hardie board have silica in it?

Working Safely with James Hardie ® Products James Hardie ® products contain crystalline silica. This mineral is found everywhere in the world – often in the form of sand – and therefore often a component of many construction products such as brick, stone, concrete, glass wool and abrasives.


Leave a Reply

Your email address will not be published. Required fields are marked *